Description
Alfa Laval 250L Biokinetics Mixer Skid
Specifications:
- HyNetics® Mixing Technology Vessel
304 Stainless Steel Welded Constructions
Fixed Sides and Bottom, Open Top
Hexagon Shaped Body and 15° Cone
Bead Blasted Interior and Exterior
Full Length Sight Glass Window fitted into one (1) Hexagon Panel on 100 Liter Units
Access Door for Liner loading and unloading, 250L and up
Sight Glass Window,
Manual Latches,
Hard-wired Interlock
Two (2) Process Tube Ports – Inlet, Outlet or Recirculation
One (1) 1 ½” Tri-Clamp Temperature Sensor Port
One (1) Agitator Drive Port
One (1) Powder Feed Port Support
Three (3) Tubular Leg Supports
- HyNetics® Mixing Technology Mixer Drive
Non-Adjustable, Vertical Stroke per table below
Non-Variable Sine Wave Profile
Variable Mixing Speed from 0.01 to 2.0Hz, 10:1 Turndown
Sizes 100 Liter and up: 230/480V, 3φ, 60Hz, 1750 RPM TEFC, XE, IP65 Motor
Size 30 Liter: 90VDC Permanent Magnet, TENV motor:
250 Liter Stroke 6” – 3.0 HP
- Automated Inflate and Purge System
One (1) ¾” Two-Way 24VDC Solenoid Valve for Automated Process Venting
Two (2) ½” Two-Way 24VDC Solenoid Valves for Automated Inflation and Purging
One (1) ½” Pressure Regulator, 0-15 psig with Pressure Indicator
- Filter Rack
One (1) 304 SS Welded Tubular Frame with capacity for four (4) Disposable Filters
Four (4) 1 ½” Tri-Clamp Hanger Assemblies to support the Disposable Filters
- HyNetics® Mixing Technology Instruments and Controls
One (1) Panel Mounted Low DP Sensing, Indicating and Transmitting Unit, 0-10 WC (in)
One (1) Liner Vent Control Circuit with Indicator and Alarm
One (1) Two-Wire PT100 RTD Temperature Element and 4-20mA Transmitters
One (1) Panel Mounted Digital Temperature Indicator in °C
One (1) Panel Mounted Digital Speed Indicator in Hertz
Relay Control Logic with Manual Pushbutton and Selector Switch Interface, Hardwired Interlocks, 24
VDC Power Supply and Circuit Breakers
NEMA4X Electrical and Controls Enclosure with Local Disconnect
Built to UL and NEC 508A Standards, UL Labeled Pane
The System is also configured with the following Options:
- Jacketed Mixing Vessel
ASME Dimple Walled Jacket – Full Vacuum to 60 PSIG MWP, 140°F MWT
ASME Pressure Relief Valve
SS Body & Trim, Mounted on Jacket Outlet, Vented to Floor
One (1) Jacket Fluid Inlet and One (1) Jacket Fluid Outlet
¾” NPT for 100 to 750
Liters Insulation – 1 ½” Polyamide Foam
304 Stainless Steel Welded Sheathing, Bead Blasted Finish
- Tank Weigh System
Three (3) Mettler-Toledo “Ring-Mount” Load Cells with Range Equal to the Vessel
Capacity, Accuracy ± 0.02% Full Scale
One (1) Mettler-Toledo Summation Box
One (1) Mettler-Toledo “Lynx” Weight Indicating Controller
One (1) High Weight Monitoring and Alarm Circuit
- Peristaltic Pump
One (1) Peristaltic Tube Pump, up to 37 LPM @ 7.5 PSIG using 1” ID Tubing
Variable Pumping Rate, 30:1 Turndown
1/2 HP, 90VDC 1750 RPM TENV, XE, IP65 Motor
Variable Speed Drive, NEMA 4 Mount, 120V, 1φ, 60Hz
Digital Speed Sensor with Panel Mounted Indicator: RPM or LPM
Connected Utility Requirements
- Inflation or Cover Gas – Any non-combustible gas, clean and dry
5 to 10 CFM @ 30 PSIG
Ambient Temperature o Connection ¾” Tri-Clamp style Sanitary Flange
Disposable Filtration @ 0.2 Micron
- Water – Any quality water suitable for Product
10 to 45 LPM @ 30 PSIG
50°C Maximum o Connection – 1” Tri-Clamp style Sanitary Flange
- Vent – Chamber expels into Room
5 to 45 LPM
Tempered to 50°C Maximum
Connection – 1” Tri-Clamp style Sanitary Flange
Disposable Filtration @ 0.2 Micron
- Power – Controls, Instruments & Accessories
120 VAC, 1 PH, 50-60 Hz, 20 Amp Service
Dedicated or UPS Preferred
- Power – AC Motor Drive, Only
30 Liter 120 VAC, 1 PH, 50-60 Hz, 20 Amp Service
100 Liter 240 VAC, 1 PH, 50-60 Hz, 10 Amp Service
250 Liter 480 VAC, 3 PH, 50-60 Hz, 20 Amp Service
750 Liter 480 VAC, 3 PH, 50-60 Hz, 20 Amp Service
- Optional Jacket Fluid
Water or Propylene Glycol, 30% Mixture
Temperature -5°C to 60°C
15 to 45 GPM @ 60 PSIG, Max.
gk – TLR53
Ebay
